Runn is not showing any speed although connected/paired with garmin watch and Zwift

Follow
Konstantinos Kavvathas
Using Runn for the last couple of months. Everything was fine till today that no speed was shown (it remained as zero) although Runn was paired with Zwift and Garmin watch. As well, Configurez finds it too. Thank you
0

Comments

14 comments

Date Votes
  • kevin phillips

    How do you re-load the firmware?

    1
    Comment actions Permalink
  • Steve Norman

    I have the same issue.  Lost an hour this morning messing around trying to get the unit to work - missed out on doing my run :(

    Can anyone point me in the right direction of how to reload the firmware please?

    1
    Comment actions Permalink
  • Nigel

    I have the same issue. It has been perfect for months then last week the speed would not be detected. I put the RUNN in the sensor speed  checking mode (LEDs did not switch as the treadmill was running) and this did not work either independent of ZWIFT, Configurez and Runcline on the Iphone. The battery was 93% charged. I try resetting the unit as instructed on the website. This did nothing. The unit would bluetooth connect and even provide incline data to runcline just no indication of speed. Strangely I then put power on to the back and the first time I did this it started work ! Yesterday the same happened again. This time it took an hour of doing the same test to get it back running. Again applying the power cable and wiggling it. Is there a firmware issue here or is the unit fault. Annoyingly it it stop working completely it would be a return to the ZWIFT store but it is so hit and miss when it is or not working.  

    0
    Comment actions Permalink
  • Chris Glover

    Same here. Fully charged. Connected showing incline fine but no speed

    0
    Comment actions Permalink
  • ALEX GAJARDO SUTHERLAND

    I have the same problem. From one day to the next I stop marking speed. And it does not allow the option to search for markers, it does not react to the click of the button. can it be for the last update?

    0
    Comment actions Permalink
  • Chris Glover

    I raised a ticket and they sent me files to manually re-load the firmware and its all working fine again

    0
    Comment actions Permalink
  • Jason Sutcliffe

    Try putting your treadmill up to 18kph for a minute or two. You don't need to be running on it of course.

     

    0
    Comment actions Permalink
  • kevin phillips

    Forget that, just did it and got it back up and running.

    0
    Comment actions Permalink
  • kevin phillips

    You need to email support who will send a zip file and full instructions.

    0
    Comment actions Permalink
  • Steve Norman

    Thanks Kevin - I've created a ticket and referred to this thread - hopefully that will do the job.

    0
    Comment actions Permalink
  • Eberhard Morgenroth

    I have the same problem. The Runn worked well, when I first installed it a three days ago. A day later, the Runn still connects to GymTrakr and transmits incline. But no transmission of speed. I did a factory reset. The firmware version was and is 3.1.8. No improvement with factory reset.

    I tried moving the Runn above stickers at all kinds of distances and angles. No response at all. Is there an independent way of checking the two sensors?

    0
    Comment actions Permalink
  • Cat Fish

    wow, many people having same problem look like, mine too stop working after 6 session, no speed and cadence broadcasting both BT and Ant+, not sure about incline I did not checked at the time,can not get in to detecting mode, both BT and Ant+ connection established to Zwift normally, well, may took little longer than usual possibly, censer IR light is lit check thru cell phone camera, firmware 3.1.8 as well, runn just do not want pick up marking.

    0
    Comment actions Permalink
  • Carlos Vasquez

    Hi.

    The exact same thing happens with my unit that I purchased (zwift) a week ago. I installed it and it worked well in four runs and then it did not report the speed, I updated the version and nothing changed, manually I brought the device closer to the band and added one more sticker as one of the solutions that they present and nothing. Incline degrees is capture OK, but not speed. I DO NOT KNOW WHAT TO DO. 

    0
    Comment actions Permalink
  • Fred cerdeira

    Same problem here. Any help?

    0
    Comment actions Permalink

Please sign in to leave a comment.

Didn't find what you were looking for?

New post